Cause all that matters here is passing the Cisco ccna 200 120 vs 200 125 exam. Cause all that you need is a high score of ccna 200 120 vs 200 125 CCNA Cisco Certified Network Associate CCNA (v3.0) exam. The only one thing you need to do is downloading Ucertify ccna 200 125 study guide exam study guides now. We will not let you down with our money-back guarantee.
Q131. - (Topic 8)
Which component of the routing table ranks routing protocols according to their preferences?
A. administrative distance
B. next hop
D. routing protocol code
Administrative distance - This is the measure of trustworthiness of the source of the route. If a router learns about a destination from more than one routing protocol, administrative distance is compared and the preference is given to the routes with lower administrative distance. In other words, it is the believability of the source of the route.
Q132. - (Topic 8)
Which statement about named ACLs is true?
A. They support standard and extended ACLs.
B. They are used to filter usernames and passwords for Telnet and SSH.
C. They are used to filter Layer 7 traffic.
D. They support standard ACLs only.
E. They are used to rate limit traffic destined to targeted networks.
Named Access Control Lists (ACLs) allows standard and extended ACLs to be given names instead of numbers. Unlike in numbered Access Control Lists (ACLs), we can edit Named Access Control Lists. Another benefit of using named access configuration mode is that you can add new statements to the access list, and insert them wherever you like. With the legacy syntax, you must delete the entire access list before reapplying it using the updated rules.
Q133. - (Topic 5)
Refer to the exhibit.
A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three.)
A. host A IP address: 192.168.1.79
B. host A IP address: 192.168.1.64
C. host A default gateway: 192.168.1.78
D. host B IP address: 192.168.1.128
E. host B default gateway: 192.168.1.129
F. host B IP address: 192.168.1.190
It’s a “router-on-a-stick” configuration. Which means each host in the VLAN must corresponds with the VLAN configured on the sub-interfaces.
VLAN 10 is configured on fa0/0.10 and VLAN 20 on fa0/0.20. So each hosts in VLAN 10 must use fa0/0.10 IP address as their default gateway, each hosts must also be in the same subnet as fa0/0.10 IP – same with hosts in VLAN 20.
So find out the usable IP addresses on each sub-interfaces – for 192.168.1.78 /27: 192.168.1.65 – .94 and for 192.168.1.130 /26: 192.168.1.128 – .190.
Host A (using port 6 – VLAN 10) must use IP 192.168.1.79, default gateway 192.168.1.78. Host B (using port 9 – VLAN 20) must use IP 192.168.1.190, default gateway
Q134. - (Topic 8)
You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.
Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.
NAT is enabled on router R1.
The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.
R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.
You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.
Examine the DHCP configuration between R2 and R3; R2 is configured as the DHCP server and R3 as the client. What is the reason R3 is not receiving the IP address via DHCP?
A. On R2. The network statement In the DHCP pool configuration is incorrectly configured.
B. On R3. DHCP is not enabled on the interface that is connected to R2.
C. On R2, the interface that is connected to R3 is in shutdown condition.
D. On R3, the interface that is connected to R2 is in shutdown condition.
Please check the below:
Q135. - (Topic 8)
Which switching method duplicates the first six bytes of a frame before making a switching decision?
A. fragment-free switching
B. store and-forward switching
C. cut through switching
D. ASIC switching
Explanation: Cut and Through method has lowest latency. In this method Switch only read first six bytes from frame after the preamble. These six bytes are the destination address of frame. This is the fastest method of switching. This method also processes invalid frames. Only advantage of this method is speed.
Q136. CORRECT TEXT - (Topic 7)
A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed.
The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted.
Access to the router CLI can be gained by clicking on the appropriate host.
All passwords have been temporarily set to "cisco".
The Core connection uses an IP address of 198.18.247.65
The computers in the Hosts LAN have been assigned addresses of 192.168.240.1 - 192.168.240.254
✑ host A 192.168.240.1
✑ host B 192.168.240.2
✑ host C 192.168.240.3
Corp1(config)# access-list 128 permit tcp host 192.168.240.1 host 172.22.141.26 eq www Corp1(config)# access-list 128 deny tcp any host 172.22.141.26 eq www
Corp1(config)# access-list 128 permit ip any any Corp1(config)#int fa0/1
Corp1(config-if)#ip access-group 128 out Corp1(config-if)#end
Corp1#copy run startup-config
Q137. - (Topic 8)
What is the first step in the NAT configuration process?
A. Define inside and outside interfaces.
B. Define public and private IP addresses.
C. Define IP address pools.
D. Define global and local interfaces.
Q138. - (Topic 4)
The output of the show frame-relay pvc command shows "PVC STATUS = INACTIVE". What does this mean?
A. The PVC is configured correctly and is operating normally, but no data packets have been detected for more than five minutes.
B. The PVC is configured correctly, is operating normally, and is no longer actively seeking the address of the remote router.
C. The PVC is configured correctly, is operating normally, and is waiting for interesting traffic to trigger a call to the remote router.
D. The PVC is configured correctly on the local switch, but there is a problem on the remote end of the PVC.
E. The PVC is not configured on the local switch.
The PVC STATUS displays the status of the PVC. The DCE device creates and sends the report to the DTE devices. There are 4 statuses:
+ ACTIVE: the PVC is operational and can transmit data
+ INACTIVE: the connection from the local router to the switch is working, but the connection to the remote router is not available
+ DELETED: the PVC is not present and no LMI information is being received from the Frame Relay switch
+ STATIC: the Local Management Interface (LMI) mechanism on the interface is disabled (by using the “no keepalive” command). This status is rarely seen so it is ignored in some books.
Q139. - (Topic 8)
Which two options are primary responsibilities of the APIC-EM controller? (Choose two.)
A. It automates network actions between different device types.
B. It provides robust asset management.
C. It tracks license usage and Cisco IOS versions.
D. It automates network actions between legacy equipment.
E. It makes network functions programmable.
Q140. - (Topic 8)
Which two statements about IPv6 and routing protocols are true? (Choose two.)
A. Link-local addresses are used to form routing adjacencies.
B. OSPFv3 was developed to support IPv6 routing.
C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
D. Loopback addresses are used to form routing adjacencies.
E. EIGRPv3 was developed to support IPv6 routing.
To know more about the 200-125, click here.