The Only Tip You Need: ccna 200 125 book

200-125 Guide

200-125 Exam Royal Pack (In Stock.)

 
  • Cisco
  • Exam Number/Code 200-125
  • Product Name CCNA Cisco Certified Network Associate CCNA (v3.0)
  • Questions and Answers
  • 635 Q&As
  • Last Updated
  • Nov 06,2018
  • List Price
  • $128.99
  • Price
  • Today 49.99 USD

Free TrialVersion: demo Buy Now 50% OFF

The Only Tip You Need: ccna 200 125 book

Exam Code: ccna 200 125 study guide (Practice Exam Latest Test Questions VCE PDF)
Exam Name: CCNA Cisco Certified Network Associate CCNA (v3.0)
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass ccna 200 125 book Exam.

Q81.  - (Topic 4)

Refer to the exhibit.

What is the meaning of the term dynamic as displayed in the output of the show frame- relay map command shown?

A. The Serial0/0 interface is passing traffic.

B. The DLCI 100 was dynamically allocated by the router.

C. The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP server.

D. The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud.

E. The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP.

Answer: E

Explanation:

Inverse Address Resolution Protocol (Inverse ARP) was developed to provide a mechanism for dynamic DLCI to Layer 3 address maps. Inverse ARP works much the same way Address Resolution Protocol (ARP) works on a LAN. However, with ARP, the device knows the Layer 3 IP address and needs to know the remote data link MAC address. With Inverse ARP, the router knows the Layer 2 address which is the DLCI, but needs to know the remote Layer 3 IP address.

When using dynamic address mapping, Inverse ARP requests a next-hop protocol address for each active PVC. Once the requesting router receives an Inverse ARP response, it updates its DLCI-to-Layer 3 address mapping table. Dynamic address mapping is enabled by default for all protocols enabled on a physical interface. If the Frame Relay environment supports LMI autosensing and Inverse ARP, dynamic address mapping takes place automatically. Therefore, no static address mapping is required.


Q82.  - (Topic 8)

Which IPv6 header field is equivalent to the TTL?

A. Hop Limit

B. Flow Label

C. TTD

D. Hop Count

E. Scan Timer

Answer: A


Q83. CORRECT TEXT - (Topic 7)

The following have already been configured on the router:

✑ The basic router configuration

✑ The appropriate interfaces have been configured for NAT inside and NAT outside.

✑ The appropriate static routes have also been configured (since the company will be a stub network, no routing protocol will be required)

✑ All passwords have been temporarily set to “cisco”.

The task is to complete the NAT configuration using all IP addresses assigned by the ISP to provide Internet access for the hosts in the Weaver LAN. Functionality can be tested by clicking on the host provided for testing.

Configuration information:

router name – Weaver

inside global addresses – 198.18.184.105 - 198.18.184.110/29 inside local addresses - 192.168.100.17 – 192.168.100.30/28 number of inside hosts – 14

A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of 192.168.100.17 – 192.168.100.30.

Answer: 

The company has 14 hosts that need to access the internet simultaneously but we just have 6 public IP addresses from 198.18.184.105 to 198.18.184.110/29. Therefore we have to use NAT overload (or PAT)

Double click on the Weaver router to open it

Router>enable Router#configure terminal

First you should change the router's name to Weaver

Router(config)#hostname Weaver

Create a NAT pool of global addresses to be allocated with their netmask. Weaver(config)#ip nat pool mypool 198.18.184.105 198.18.184.110 netmask 255.255.255.248

Create a standard access control list that permits the addresses that are to be translated.

Weaver(config)#access-list 1 permit 192.168.100.16 0.0.0.15

Establish dynamic source translation, specifying the access list that was defined in the prior step.

Weaver(config)#ip nat inside source list 1 pool mypool overload

This command translates all source addresses that pass access list 1, which means a source address from 192.168.100.17 to 192.168.100.30, into an address from the pool named mypool (the pool contains addresses from 198.18.184.105 to 198.18.184.110). Overload keyword allows to map multiple IP addresses to a single registered IP address (many-to-one) by using different ports.

The question said that appropriate interfaces have been configured for NAT inside and NAT outside statements.

This is how to configure the NAT inside and NAT outside, just for your understanding:

Weaver(config)#interface fa0/0 Weaver(config-if)#ip nat inside Weaver(config-if)#exit Weaver(config)#interface s0/0 Weaver(config-if)#ip nat outside Weaver(config-if)#end

Finally, we should save all your work with the following command:

Weaver#copy running-config startup-config

Check your configuration by going to "Host for testing" and type:

C :\\>ping 192.0.2.114

The ping should work well and you will be replied from 192.0.2.114


Q84.  - (Topic 4)

What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?

A. defines the destination IP address that is used in all broadcast packets on DCLI 202

B. defines the source IP address that is used in all broadcast packets on DCLI 202

C. defines the DLCI on which packets from the 192.168.1.2 IP address are received

D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address

Answer: D

Explanation:

This command identifies the DLCI that should be used for all packets destined to the 192.168.1.2 address. In this case, DLCI 202 should be used.


Q85.  - (Topic 8)

A router has learned three possible routes that could be used to reach a destination network One route is from EIGRP and has a composite metric of 07104371. Another route is from OSPF with a metric of 782 The last is from RIPv2 and has a metric of 4 Which route or routes will the router install in the routing table?

A. the EIGRP route

B. the OSPF route

C. the RIPv2 route

D. all three routes

E. the OSPF and RIPv2 routes

Answer: A


Q86.  - (Topic 5)

In GLBP, which router will respond to client ARP requests?

A. The active virtual gateway will reply with one of four possible virtual MAC addresses.

B. All GLBP member routers will reply in round-robin fashion.

C. The active virtual gateway will reply with its own hardware MAC address.

D. The GLBP member routers will reply with one of four possible burned in hardware addresses.

Answer: A

Explanation:

One disadvantage of HSRP and VRRP is that only one router is in use, other routers must wait for the primary to fail because they can be used. However, Gateway Load Balancing Protocol (GLBP) can use of up to four routers simultaneously. In GLBP, there is still only one virtual IP address but each router has a different virtual MAC address. First a GLBP group must elect an Active Virtual Gateway (AVG). The AVG is responsible for replying ARP requests from hosts/clients. It replies with different virtual MAC addresses that correspond to different routers (known as Active Virtual Forwarders – AVFs) so that clients can send traffic to different routers in that GLBP group (load sharing).


Q87. .  - (Topic 3)

A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?

A. It checks the configuration register.

B. It attempts to boot from a TFTP server.

C. It loads the first image file in flash memory.

D. It inspects the configuration file in NVRAM for boot instructions.

Answer: A

Explanation:

Default (normal) Boot Sequence

Power on Router - Router does POST - Bootstrap starts IOS load - Check configuration register to see what mode the router should boot up in (usually 0x2102 to read startup- config in NVRAM / or 0x2142 to start in "setup-mode") - check the startup-config file in NVRAM for boot-system commands - load IOS from Flash.


Q88.  - (Topic 3)

Why do large OSPF networks use a hierarchical design? (Choose three.)

A. to decrease latency by increasing bandwidth

B. to reduce routing overhead

C. to speed up convergence

D. to confine network instability to single areas of the network

E. to reduce the complexity of router configuration

F. to lower costs by replacing routers with distribution layer switches

Answer: B,C,D

Explanation:

OSPF implements a two-tier hierarchical routing model that uses a core or backbone tier known as area zero (0). Attached to that backbone via area border routers (ABRs) are a number of secondary tier areas. The hierarchical approach is used to achieve the following:

•Rapid convergence because of link and/or switch failures

•Deterministic traffic recovery

•Scalable and manageable routing hierarchy, reduced routing overhead.


Q89.  - (Topic 5)

Which three are the components of SNMP? (Choose three)

A. MIB

B. SNMP Manager

C. SysLog Server

D. SNMP Agent

E. Set

Answer: A,B,D

Explanation:

SNMP is an application-layer protocol that provides a message format for communication between SNMP managers and agents. SNMP provides a standardized framework and a common language used for the monitoring and management of devices in a network. The SNMP framework has three parts:

+ An SNMP manager

+ An SNMP agent

+ A Management Information Base (MIB)

The SNMP manager is the system used to control and monitor the activities of network hosts using SNMP. The most common managing system is called a Network Management System (NMS). The term NMS can be applied to either a dedicated device used for network management, or the applications used on such a device. A variety of network management applications are available for use with SNMP. These features range from simple command-line applications to feature-rich graphical user interfaces (such as the CiscoWorks2000 line of products).

The SNMP agent is the software component within the managed device that maintains the data for the device and reports these data, as needed, to managing systems. The agent and MIB reside on the routing device (router, access server, or switch). To enable the SNMP agent on a Cisco routing device, you must define the relationship between the manager and the agent.

The Management Information Base (MIB) is a virtual information storage area for network management information, which consists of collections of managed objects.


Q90.  - (Topic 5)

Which two of these statements are true of IPv6 address representation? (Choose two.)

A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.

B. A single interface may be assigned multiple IPv6 addresses of any type.

C. Every IPv6 interface contains at least one loopback address.

D. The first 64 bits represent the dynamically created interface ID.

E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.

Answer: B,C

Explanation:

✑ A single interface may be assigned multiple addresses of any type (unicast, anycast, multicast).

✑ Every IPv6-enabled interface must contain at least one loopback and one link-local

address.

✑ Optionally, every interface can have multiple unique local and global addresses.

Reference: IPv6 Addressing at a Glance – Cisco PDF


To know more about the 200-125, click here.

Tagged as : Cisco 200-125 Dumps, Download 200-125 pdf, 200-125 VCE, 200-125 pass4sure, examcollection 200-125